Pen Making Supplies Logo
Have You Signed up for our Mailing List packed with free stuff, great offers and more??? 		Free Catalog
Penmaking Home Penmaking Index Page Penmaking Index Page Penmaking Index Page Pen Making Kits Pen Making Supplies Pen Making Supplies Penmaking Tools WoodWorkingCrafts.com Forums Steebar Home Page Pen Making Kits
Pen Making Supplies PK-1013, 1014 Slimline Pen and Pencil Kit Assembly Instructions Pen Making Supplies
Looking for Penmaking Instruction Sheets? | Search for:
PK-1013, 1014 Slimline Pen and Pencil Kit Assembly Instructions
KIT FEATURES
• Heavy 24kt Gold Plating with Epoxy Coating.
• Both products are designed to match as a set.
• Simplified construction, uses same tube lengths for both kits. (2-1/32" long).
• Pen Features a New Locking Mechanism.
• Pencil Features a New Trouble Free 0.7mm Lead Mechanism
• A Variety of Clip and Band Styles are Available.
• Overall Length: Pen= 5-1/8", Pencil= 5-5/8"
 REQUIRED ACCESSORIES
• 7mm Long Mandrel.
• 3 Piece Bushing Set PK-1259.
• 7mm Drill Bit PK-1173.
• 7mm Barrel Trimmer PK-1125 (optional)
• 2 Part Epoxy Glue or SG-THICK Super Glue

Step 1 - Cut Wood Blanks
From 1/2" to 5/8" square stock, cut blanks to the length of the tube plus 1/16". Grain should run lengthwise.

Step 2 - Drill The Wood Blanks
Drill a 7mm centered hole lengthwise through each blank. Excessive pressure will cause the drill bit to wander and/or split the blank. Slow the feed rate and back the bit out repeatedly for chip removal.

Step 3 - Glue The Tubes Into The Blanks
Use epoxy or a gap filling cyanoacrylate. Spread the glue on the tube. Insert into the blank with a twisting motion to spread the glue evenly inside. Center each tube lengthwise in the blank. Allow it to dry.

Step 4 - Square The Ends
With a 7mm barrel trimmer PK-1125 or other sanding device, square the ends of the blanks 90 degrees flush to the ends of the brass tubes.

Step 5 - Turning The Blanks
Place the stop bushing onto the mandrel hand tight.
Place one of the other bushings onto the mandrel, slide on either blank, then another bushing.
Follow with the second blank then the last bushing.
Thread on the lock nut hand tight. Bring the tail stock snug with the mandrel (do not over tighten, it could damage the mandrel) slide the stop bushing toward the blank. Adjust to remove the space then tighten set screw and lock nut.
Turn the blanks down to a diameter slightly larger than the bushings (about 11/32" O.D.). As you approach the final size be careful since the wood is only about 1/32" thick.

Step 6 - Sand
As with any sanding, progress through a range of grits.
The type of wood used and the quality of the beginning surface will dictate your selection:
• 80-100 grit if a rough surface or additional shaping is needed (overly thick)
• 120-150 grit if fairly smooth and straight
• 220-240 for final finish with most domestic woods
• 320-400 especially on dense or oily exotic woods
Scotch Brite® is helpful and doesn’t tend to scratch.
Sand with blank spinning. Finally sand with the grain (lathe off). For initial shaping, stick some sandpaper on a board 2" wide to remove any hills or valleys. The center ring is 21/64" in dia. The final size for a flush finish is between 5/16" & 11/32". For a little heavier look, just form a little thicker barrel.

Step 7 - Finish
Try a finish of your choice but be careful if brushing on a poly, etc. You can stick the tube, bushings, and mandrel together.
You could also use Hut Perfect Pen Polish PK-1114 & PK-1115.

Step 8 - Touch Up
With tubes off mandrel, lay them end to end to decide which sets will look best when assembled. Remember, they will be 5/32” apart (due to center ring) so minor differences won’t show. If necessary, a light sanding of the ends on a block will square the ends and improve the fit during assembly. Then repeat step 7.
General Assembly Hints:
• Use a clamp or vise to press parts together.
• Front and rear tubes are identical on both pen and
pencil kits and may be mixed and matched.
• 7mm Pen Disassembler Kit, PK-1121 is available.

Diagram B - Assembly of Pen
Note: Line up parts according to layout below.
A. Press the tip into the front tube.
B. Press the twist mechanism (brass end first) into opposite end of same tube (usually to the indentation mark). Don’t press too far in!
C. Slide band over the exposed mechanism.
D. Press cap into the clip then onto the rear tube (clip can be left off if desired). 		E. Push the two halves together aligning grain as desired. Pen is operated by twisting the halves in opposite directions to extend or retract point. Test the extension with the refill inserted. Uses Cross® type refills.

Diagram C - Assembly of Pencil
Note: Line up parts according to layout below.
A. Press the sleeve, recessed end first into the end of the front barrel until it hits the shoulder.
B. Press the band into the opposite end of the barrel.
C. Press the rear barrel onto the band.
D. Press cap into the clip then onto the rear tube (clip can be left off if desired).
E. Insert mechanism through the cap and out the opposite end.
F. Screw the tip tightly onto the threaded end of the mechanism.
 G. The pencil operates by pushing down on the plunger. This clicks the lead out. The eraser and extra lead is located under the gold cap on the mechanism. Use 0.7mm lead.
Note: If lead does not advance properly or retracts when writing, gently pull exposed short piece of lead out of mechanism. Continue to pump pencil plunger until a new piece of lead is exposed.

Search our site:
Search for:

Jump directly to a specific page

Want the inside scoop?

News and information, Steebar Exclusives,
Special Offers, Free Stuff and more!
Signup Here ..

On PenMakingSupplies.com you will find a complete line of Pen making kits, supplies and turning tools for the serious pencrafter. If there's something you can't find just send us an email and we'll be glad to point you in the right direction. Don't forget to stop by our wood working craft site WoodWorkingCrafts.com.

You may also be interested in our Clock Parts and Clock Making Supplies...


P.O. Box 607  Peapack, New Jersey 07977
Phone: (908) 204-0095 Fax: (908) 204-0099
Copyright © 2005, Steebar Corp.
Penmaking supply partner sites

 

 


pen making, pen supplies, pocket watch, pendant watch, pendant watch kits, liquid glass, epoxy resin, liquid glass epoxy